Set Post Configuration Inputs in GibbsCAM 2024

Summary

GibbsCAM 2024 allows an updated post processor to display standard options, custom selections, and user-entered values on the Post dialog Configuration tab. The active post defines the available inputs and how each setting affects NC output.

Table of Contents

What Changed in GibbsCAM 2024
Before You Begin
Procedure
Related Video
Best Practices
Troubleshooting
Related Articles

What Changed in GibbsCAM 2024

Area	GibbsCAM 2024 Change	Dependency
Post Configuration	The Post dialog can display post-defined checkboxes, lists, and value fields on the Configuration tab.	The active post must be updated for GibbsCAM 2024 and programmed to expose the inputs.

Important: Configuration labels and output effects are specific to the active post. Do not assume that an option behaves the same way in another post or machine configuration.

Before You Begin

• Use GibbsCAM 2024 or later with the approved machine definition and post processor.

• Confirm the post name, revision, target control, and whether the post was updated for GibbsCAM 2024.

• Obtain the approved values and expected output behavior for each Configuration input.

• Save the part and create a baseline NC file before changing any post input.

Procedure

Step 1 - Confirm the Active Post

1. Open the Post dialog and verify the machine, control, post name, and post revision.

2. If the post is legacy or has not been updated for GibbsCAM 2024, obtain the supported post before relying on Configuration inputs.

Step 2 - Review the Configuration Tab

1. Select the Configuration tab.

2. Review the checkboxes, lists, and value fields supplied by the active post.

Figure 1 The Configuration tab displays the inputs defined by the active GibbsCAM 2024 post Source: What's New in GibbsCAM 2024, p. 19

3. Compare the displayed controls with the post documentation or CAMCO instructions for that revision.

Step 3 - Test One Input

1. Change one approved input and post a controlled test file.

2. Compare the new output with the baseline and identify the blocks, codes, comments, or formatting changed by that input.

3. Restore the approved value before testing another input.

Step 4 - Validate the Final Output

1. Set every Configuration input to its approved production value.

2. Post a new file and compare the result with the setup sheet, control requirements, and qualified baseline.

3. Complete the normal posted-code review and machine prove-out before production release.

Expected Result

• The Configuration tab displays the inputs defined by the active post.

• Each tested input changes output only as documented for the selected post and job conditions.

• The final NC file reflects the approved Configuration values.

Best Practices

• Document each input, its allowed values, and its expected output effect for the qualified post revision.

• Change one input at a time while qualifying a post.

• Retain baseline and test files so unexpected changes can be compared directly.

• Include the part, post, machine files, and supporting details in a Pack and Go package when requesting support.

Troubleshooting

• Problem: The Configuration tab is missing or empty.

Cause

• The active post was not updated for GibbsCAM 2024.

• The post does not define user-facing inputs, or a different post is active.

Resolution

Verify the post name and revision and select the approved GibbsCAM 2024 post. Contact the post developer or CAMCO if that post should expose inputs but does not.

• Problem: An expected Configuration input is missing.

Cause

• The selected post revision does not include the input.

• The input is available only for another machine, control, or post configuration.

Resolution

Compare the active post with the qualified revision and its documentation. Do not substitute an unrelated setting; request the correct post or a validated update.

• Problem: Changing an input does not change the output.

Cause

• The input is not mapped to output in the active post.

• The job conditions do not trigger the option, or the file was posted with a previous setting or different post.

Resolution

Confirm the active post, change one input, and create a new controlled output. Compare it with the baseline and request post-specific guidance if no documented effect appears.

• Problem: The output changes in an unexpected way.

Cause

• The input has a post-specific effect that differs from the expected behavior.

• Several inputs changed at the same time, making the cause unclear.

Resolution

Stop release, restore the baseline, and retest one input at a time. Provide CAMCO with the part, post, machine files, baseline, test output, and exact settings if the difference remains.

• What's New in GibbsCAM 2024

• Legacy Post Warning

• Error Unable to Read Post Processor

• How to Create a Pack and Go File